________________________________________________________________________________
General Technical Data
Perkins 4.248 Engine Specifications
Engine Model ........ A4.248
Engine Type ........ Four Stroke, direct injection diesel
Nominal Bore, in (mm) ........ 3.975 (100,96)
Stroke, in (mm) ........ 5,0 (127,0)
Cycle ........ Four Stroke
No. of Cylinders ........ 4
Cylinder Arrangement ........ In-Line
Cubic Capacity, cu.in (L) ........ 248 (4,06)
Maximum Power Rating, kW (Hp) ........ 62,0 (84,0)
Nominal Power Rating, kW (Hp) ........ 59,0 (80,0)
Rated Engine Speed, rpm ........ 2500
Maximum Torque, Nm (Ibf-ft) ........ 263 (194)
Torque Speed, prm ........ 1400
Compression Ratio ........ 15.5:1
Induction System ........ Naturally aspirated
Direction of Engine Rotation ........ Clockwise from the Front
Firing Order ........ 1-3-4-2
Fuel System
Fuel Injection Pump Make ........ CAV
Fuel Injection Pump Type ........ DPA
Injection Pump Rotation ........ Clockwise
Injection Pump Plunger Dia ........ 8,5 mm
Combustion System ........ Direct Injection
Fuel Lift Pump Type ........ A.C. Delco. V.P. Series
Fuel Lift Pump Method of Drive ........ Eccentric on Camshaft
Fuel Filter Element Type ........ Paper
Fuel Filter Valve Type ........ Gravity Vent Valve
Lubricating System
Relief Valve Type ........ Spring loaded plunger
Pressure Setting ........ 5,86 bar
Oil Pump Type ........ Rotor type
Lubricating Oil Filter Type ........ Full Flow
Dimensions
Width, in (mm) ........ 27.96 (710)
Height, in (mm) ........ 30.51 (775)
Depth, in (mm) ........ 20.95 (532)
Weight, lbs (kg) ........ 750 (340)
Perkins 4.248 Maintenance Data
Engine oil type ........ SAE 10W-30/15W-40
Engine oil capacity, L (qts) ........ 8.0 (8.4)
Coolant capacity, L (qts) ........ 15.6 (16.5)
Oil filter change interval ........ Every 250 hours
Oil change interval ........ Every 250 hours
Fuel filter change interval ........ Every 500 hours
Perkins 4.248 Service Specifications
Wear Limits
Cylinder Head Bow Wear Limit (Transverse), in (mm) ........ 0,003 (0,08)
Cylinder Head Bow Wear Limit (Longitudinal), in (mm) 0,006 (0,15)
Cylinder Head Maximum Bore Wear Limit, in (mm) ........ 0,008 (0,2)
Crankshaft Main and Big End Journal Wear Ovality, in (mm) ........ 0,0015 (0,04)
Maximum Crankshaft End Float Wear Limit, in (mm) ........ 0,015 (0,38)
Valve Stem to Bore/Guide Clearance (inlet), in (mm) ........ 0,005 (0,13)
Valve Stem to Bore/Guide Clearance (exhaust), in (mm) ........ 0,006 (0,15)
Valve Head Thickness Between Run-out of Valve Seat and Face of Valve, in (mm) ........ 0,0312 (0,79)
Rocker Clearance on Rocker Shaft, in (mm) ........ 0,005 (0,13)
Camshaft Journals (Ovality and Wear), in (mm) ........ 0,002 (0,05)
Camshaft End Float, in (mm) ........ 0,020 (0,51)
Idler Gear End Float, in (mm) ........ 0,010 (0,25)
Valve Head Depth below Cylinder Head Face (exhaust, earlier), in (mm) ........ 0,055 (1,40)
Valve Head Depth below Cylinder Head Face (exhaust, current), in (mm) ........ 0,073 (1,85)
Valve Head Depth below Cylinder Head Face (inlet), in (mm) ........ 0,061 (1,55)
Cylinder Block
Total Height of Cylinder Block between Top and Bottom Faces, in (mm) ........ 17,367-17,375 (441,12-441,33)
Parent Bore Diameter for Cylinder Liner (Chrome Thin Wall), in (mm) ........ 3,9325-3,9635 (100,65-100,67)
Parent Bore Diameter for Cylinder Liner (Chrome Thick Wall), in (mm) ........ 4,0625-4,0635 (103,19-103,22)
Parent Bore Diameter for Flangeless Cylinder Liner (Cast Iron), in (mm) ........ 4,0615-4,0625 (103,16-103,19)
Parent Bore Diameter for Flanged Cylinder Liner (Cast Iron), in (mm) ........ 4,1025-4,1035 (104,20-104,23)
Depth of Recess for Liner Flange (Cast Iron), in (mm) ........ 0,150-0,154 (3,81-3,91)
Depth of Recess for Liner Flange (Chrome Thin Wall) early type, in (mm) ........ 0,046-0,049 (1,17-1,25)
Depth of Recess for Liner Flange (Chrome Thin Wall) later type, in (mm) ........ 0,049-0,051 (1,25-1,30)
Depth of Recess for Liner Flange (Chrome Thick Wall, in (mm) ........ 0,150-0,152 (3,81-3,86)
Main Bearing Parent Bore Diameter, in (mm) ........ 3,166-3,167 (80,42-80,44)
Camshaft Bore Diameter No. 1 for Bush (where fitted), in (mm) ........ 2,1875-2,1887 (55,56-55,59)
Camshaft Bearing Bush Internal Diameter fitted, in (mm) ........ 2,0000-2,0017 (50,8-50,84)
Camshaft Bore Diameter No. 1, in (mm) ........ 2,000-2,001 (50,80-50,83)
Camshaft Bore Diameter No. 2, in (mm) ........ 1,990-1,9918 (50,55-50,59)
Camshaft Bore Diameter No. 3, in (mm) ........ 1,970-1,9718 (50,04-50,08)
Cylinder Liners
Cylinder Liner O.D. (Flangeless), in (mm) ........ 4,0660-4,0670 (103,27-103,30)
Cylinder Liner O.D. (Flanged), in (mm) ........ 4,1045-4,1055 (104,25-104,28)
Cylinder Liner O.D. (Non-Flame Ring), in (mm) ........ 4,1045-4,1055 (104,25-104,28)
Flanged Pre-Finished Service Liner O.D., in (mm) ........ 4,1025-4,1035 (104,20-104,23)
Flanged Pre-Finished Service Liner O.D. (non-Flame Ring), in (mm) ........ 4,1025-4,1035 (104,20-104,23)
Interference Fit Liner in Cylinder Block (Flangeless), in (mm) ........ 0,003-0,005 (0,08-0,13)
Interference Fit Liner in Cylinder Block (Flanged), in (mm) ........ 0,001-0,003 (0,03-0,08)
Interference Fit Liner in Cylinder Block (Non-Flame Ring), in (mm) ........ 0,001-0,003 (0,03-0,38)
Transition Fit of Pre-Finished Service Liner, in (mm) ........ 0,001 (0,03)
Finished Bore Diameter of Production Liners, in (mm) ........ 3,9785-3,9795 (101,05-101,07)
Bore Diameter of Pre-Finished Service Liner in Block, in (mm) ........ 3,980-3,981 (101,09-101,12)
Height of Top of Liners above Cylinder Block Face, in (mm) ........ 0,028-0,037 (0,71-0,94)
Flange Thickness of Liner, in (mm) ........ 0,150-0,152 (3,81-3,86)
Relationship of Liner Flange to Cylinder Block Face, in (mm) ........ 0,002 (0,03) Above to 0,004 (0,10) Below
Overall Length of Liner (Flangeless), in (mm) ........ 8,805-8,815 (223,65-223,90)
Perkins A4.248 Cylinder Head
Cylinder Head Length, in (mm) ........ 19,875 (504,82)
Cylinder Head Depth, in (mm) ........ 4,0625 ± 0,015 (103,20 ± 0,38)
Skimming allowance on Cylinder Head Face, in (mm) ........ 0,012 (0,30)
Minimum Cylinder Head Depth after Skimming, in (mm) ........ 4,0355 (102,51)
Maximum Nozzle Protrusion after Skimming, in (mm) ........ 0,175 (4,44)
Leak Test Pressure ........ 2,06 bar
Valve Seat Angle ........ 45 deg
Valve Bore in Cylinder Head, in (mm) ........ 0,37425-0,37525 (9,51-9,53)
Valve Guide Parent Bore Diameter, in (mm) ........ 0,6247-0,6257 (15,87-15,89)
Clearances between Valve Stem and Rocker Lever, in (mm) ........ 0,012 (0,30)
Inner Valve Springs Fitted Length, in (mm) ........ 1,5625 (39,7)
Outer Valve Springs Fitted Length, in (mm) ........ 1,780 (45,22)
Valve Guides
Inside Diameter (Inlet and Exhaust), in (mm) ........ 0,375-0,376 (9,53-9,55)
Outside Diameter, in (mm) ........ 0,6259-0,6265 (15,89-15,91)
Interference Fit of Guide in Cylinder Head Bore, in (mm) ........ 0,0002-0,0018 (0,005-0,046)
Depth of Counterbore (Exhaust Guide), in (mm) ........ 0,4062 (10,32)
Overall Length of Guide (Exhaust), in (mm) ........ 2,4375 (61,92)
Overall Length of Guide (Inlet), in (mm) ........ 2,281 (57,94)
Guide Protrusion Above Cylinder Head Top Face, in (mm) ........ 0,594 (15,09)
Exhaust Valves
Valve Stem Diameter, in (mm) ........ 0,372-0,3728 (9,45-9,47)
Clearance Fit of Valve in Guide (if fitted), in (mm) ........ 0,00225-0,004 (0,06-0,10)
Clearance Fit of Valve in Head, in (mm) ........ 0,00145-0,00325 (0,04-0,08)
Valve Head Diameter, in (mm) ........ 1,435-1,445 (36,45-36,70)
Valve Face Angle ........ 45 deg
Valve Head Depth below Cylinder Head Face (earlier), in (mm) ........ 0,029-0,039 (0,74-0,99)
Valve Head Depth Below Cylinder Head Face (current), in (mm) ........ 0,047-0,057 (1,19-1,45)
Overall Length of Valve, in (mm) ........ 4,847-4,863 (123,11-123,52)
Service Valve Stem Oversizes, in (mm) ........ 0,003; 0,015 and 0,030 (0,08; 0,38 and 0,76)
Inlet Valves
Valve Stem Diameter, in (mm) ........ 0,3725-0,3735 (9,46-9,48)
Clearance Fit of Valve in Guide (if fitted), in (mm) ........ 0,0015-0,0035 (0,04-0,09)
Clearance Fit of Valve in Head, in (mm) ........ 0,00075-0,00275 (0,02-0,07)
Valve Head Diameter, in (mm) ........ 1,736-1,746 (44,09-44,36)
Valve Face Angle ........ 45 deg
Valve Head Depth Below Cylinder Head Face, in (mm) ........ 0,035-0,045 (0,89-1,14)
Overall Length of Valve, in (mm) ........ 4,831-4,847 (122,71-123,11)
Service Valve Stem Oversizes, in (mm) ........ 0,003; 0,015 and 0,030 (0,08; 0,38 and 0,76)
Tappets
Overall Length, in (mm) ........ 2,96875 (75,41)
Outside Diameter Tappet Shank, in (mm) ........ 0,7475-0,7485 (18,99-19,01)
Cylinder Block Tappet Bore Diameter, in (mm) ........ 0,750-0,7513 (19,05-19,08)
Tappet Running Clearance in Bore, in (mm) ........ 0,0015-0,0038 (0,04-0,10)
Outside Diameter of Tappet Foot, in (mm) ........ 1,1875 (30,16)
Rocker Shaft and Rocker Levers
Overall Length of Shaft, in (mm) ........ 16,796 (426,62)
Outside Diameter of Shaft, in (mm) ........ 0,7485-0,7495 (19,01-19,04)
Inside Diameter of Lever Bore, in (mm) ........ 0,7505-0,7520 (19,06-19,10)
Lever Clearance on Rocker Shaft, in (mm) ........ 0,001-0,0035 (0,03-0,09)
Pistons (4 Rings)
Pistons Type ........ Cavity Crown
Piston Height in relation to Cylinder Block, in (mm) ........ 0,002-0,010 (0,05-0,26) above
Bore Diameter for Gudgeon Pin, in (mm) ........ 1,37485-1,37505 (34,92-34,93)
Compression Ring Groove Width (Numbers 1, 2 and 3), in (mm) ........ 0,0957-0,0967 (2,43-2,46)
Scraper Ring Groove Width (Number 4, Plain piston), in (mm) ........ 0,2525-0,2535 (6,41-6,44)
Scraper Ring Groove Width (No.4, Inserted piston), in (mm) ........ 0,189-0,190 (4,80-4,83)
Pistons (3 Rings)
Pistons Type ........ Cavity Crown
Piston Height in Relation to Cylinder Block Top Face, in (mm) ........ 0,002-0,010 (0,05-0,26) above
Bore Diameter for Gudgeon Pin, in (mm) ........ 1,37485-1,37505 (34,92-34,93)
Compression Ring Groove Width (Numbers 1 and 2), in (mm) ........ 0,1015-0,1024 (2,58-2,60)
Scraper Ring Groove Width (No. 3), in (mm) ........ 0,1984-0,1992 (5,04-5,06)
Piston Rings (4 Rings)
Top Compression Ring ........ Chrome Insert, Parallel Face/Barrel Face
2nd and 3rd Compression Rings ........ Internally Stepped
4th Scraper Ring ........ Spring Loaded Conformable
Compression Ring Width, in (mm) ........ 0,0928/0,0938 (2,36/2,38)
Ring Clearance Groove (Numbers 1, 2 and 3), in (mm) ........ 0,0019/0,0039 (0,05/0,10)
Ring Gap, Chrome, in (mm) ........ 0,016/0,034 (0,41/0,86)
Ring Gap, Cast Iron, in (mm) ........ 0,012/0,030 (0,30/0,76)
Ring Gap, Scraper, in (mm) ........ 0,012/0,036 (0,30/0,91) varies according to type
Piston Rings (3 Rings)
Top Compression Ring ........ Molybdenum Faced, Internally Stepped, Barrel Faced
Second Compression Ring ........ Internally Stepped, Taper Faced
Third Scraper Ring ........ Chrome Faced, Spring Loaded Conformable
Compression Ring Width (Number 1 and 2), in (mm) ........ 0,097/0,098 (2,46/2,49)
Compression Ring Clearance Groove (Number 1 and 2), in (mm) ........ 0,0017/0,0027 (0,04/0,07)
Scraper Ring Width, in (mm) ........ 0,1954/0,1964 (4,96/4,99)
Scraper Ring Clearance Groove, in (mm) ........ 0,002/0,0038 (0,05/0,10)
Ring Gap, Number 1, in (mm) ........ 0,016/0,034 (0,41/0,86)
Ring Gap, Number 2, in (mm) ........ 0,016/0,034 (0,41/0,86)
Ring Gap, Number 3, in (mm) ........ 0,016/0,034 (0,41/0,86)
Small End Bush
Type ........ Steel Backed, Lead Bronze Lined
Outside Diameter of Small End Bush, in (mm) ........ 1,535-1,5365 (38,99-39,03)
Length of Small End Bush, in (mm) ........ 1,316-1,336 (33,43-33,93)
Inside Diameter before Reaming, in (mm) ........ 1,359-1,363 (34,52-34,62)
Inside Diameter after Reaming, in (mm) ........ 1,37575-1,3765 (34,94-34,96)
Clearance between Small End Bush and Gudgeon Pin, in (mm) ........ 0,00075-0,0017 (0,019-0,043)
Connecting Rod
Type ........ H-Section
Cap Location to Connecting Rod ........ Serrations
Big End Parent Bore Diameter, in (mm) ........ 2,6460-2,6465 (67,21-67,22)
Small End Parent Bore Diameter, in (mm) ........ 1,53125-1,53225 (38,90-38,92)
Length from Centre Line of Big End to Centre Line of Small End, in (mm) ........ 8,624-8,626 (219,05-219,10)
Length from Centre Line of Big End to Centre Line of Big End, Width, in (mm) ........ 1,577-1,580 (40,06-40,13)
Perkins 4.248 Crankshaft
Overall Length, in (mm) ........ 24,01-24,04 (609,85-610,62)
Main Journal Diameter, in (mm) ........ 2,9984-2,9992 (76,16-76,18)
Main Journal Length (No. 1), in (mm) ........ 1,453-1,473 (36,91-37,41)
Main Journal Length (No. 2, 4 and 5), in (mm) ........ 1,545-1,549 (39,24-39,34)
Main Journal Length (No. 3), in (mm) ........ 1,738-1,741 (44,15-44,22)
Crankpin Diameter, in (mm) ........ 2,4988-2,4996 (63,47-63,49)
Crankpin Length, in (mm) ........ 1,5885-1,5915 (40,35-40,42)
Surface Finish (All Journals), micro in (microns) ........ 16 (0,4) maximum
Main Journal and Crankpin Regrind Undersizes, in (mm) ........ -0,010, 0,020 and 0,030 (-0,25, 0,51 and 0,76)
Oil Seal Helix Diameter (rope seals only), in (mm) ........ 3,124-3,125 (79,35-79,38)
Oil Seal Helix Width, in (mm) ........ 0,050-0,080 (1,27-2,03)
Oil Seal Helix Depth, in (mm) ........ 0,004-0,008 (0,10-0,20)
Flange Diameter, in (mm) ........ 5,247-5,249 (133,27-133,32)
Spigot Bearing Recess Depth, in (mm) ........ 0,781 (19,84)
Spigot Bearing Recess Bore, in (mm) ........ 1,8497-1,8502 (46,98-47,00)
Crankshaft End Float, in (mm) ........ 0,002-0,015 (0,05-0,38)
Crankshaft Thrust Washers
Type ........ Steel Backed, Aluminium Tor Lead Bronze Faced
Position in Engine ........ Centre Main Bearing
Thrust Washer Thickness (STD), in (mm) ........ 0,089-0,091 (2,26-2,31)
Thrust Washer Thickness (O/S), in (mm) ........ 0,096-0,099 (2,44-2,51)
Thrust Washer Outside Diameter, in (mm) ........ 4,088-4,098 (103,84-104,90)
Thrust Washer Inside Diameter, in (mm) ........ 3,420-3,430 (86,87-87,12)
Main Bearings
Type ........ Pre-Finished, Steel Backed, Aluminium Tor Lead Bronze Faced
Shell Width (No. 1, 2, 4, and 5), in (mm) ........ 1,245-1,255 (31,62-31,88)
Shell Width (No. 3), in (mm) ........ 1,435-1,445 (36,45-36,70)
Outside Diameter of Main Bearing, in (mm) ........ 3,167 (80,41)
Inside Diameter of Main Bearing, in (mm) ........ 3,0010-3,0026 (76,23-76,27)
Main Bearing Running Clearance, in (mm) ........ 0,0018-0,0042 (0,05-0,11)
Shell Thickness, in (mm) ........ 0,0822-0,0825 (2,088-2,098)
Connecting Rod Bearings
Type ........ Pre-Finished, Steel Backed, Aluminium Tor Lead Bronze Faced
Shell Width, in (mm) ........ 1,245-1,255 (31,62-31,88)
Outside Diameter of Connecting Rod Bearing, in (mm) ........ 2,6465 (67,22)
Inside Diameter of Connecting Rod Bearing, in (mm) ........ 2,5008-2,5019 (63,52-63,55)
Connecting Rod Bearing Running Clearance, in (mm) ........ 0,0012-0,0031 (0,03-0,08)
Shell Thickness, in (mm) ........ 0,0723-0,0726 (1,836-1,844)
Perkins 4.248 Camshaft
Journal Diameter (Number 1), in (mm) ........ 1,9965-1,9975 (50,71-50,74)
Cylinder Block Camshaft Bore Diameter (Number 1), in (mm) ........ 2,000-2,001 (50,8-50,83)
Journal Running Clearance (Number 1), in (mm) ........ 0,0025-0,0045 (0,06-0,11)
Journal Diameter (Number 2), in (mm) ........ 1,9865-1,9875 (50,46-50,48)
Cylinder Block Camshaft Bore Diameter (Number 2), in (mm) ........ 1,990-1,992 (50,55-50,60)
Journal Running Clearance (Number 2), in (mm) ........ 0,0025-0,0053 (0,06-0,14)
Journal Diameter (Number 3), in (mm) ........ 1,9665-1,9675 (49,95-49,98)
Cylinder Block Camshaft Bore Diameter (Number 3), in (mm) ........ 1,970-1,972 (50,04-50,09)
Journal Running Clearance (Number 3), in (mm) ........ 0,0025-0,0053 (0,06-0,14)
Cam Lift, in (mm) ........ 0,300-0,303 (7,62-7,70)
Oilways for Rocker Shaft Lubrication, in (mm) ........ No.2 Journal
Camshaft Thrust Washer
Type ........ 360 degrees
Thrust Washer Outside Diameter, in (mm) ........ 2,872-2,874 (72,95-73,00)
Cylinder Block Recess Diameter for Thrust Washer, in (mm) ........ 2,875-2,885 (73,03-73,28)
Clearance Fit of Washer in Recess, in (mm) ........ 0,001-0,013 (0,03-0,33)
Thrust Washer Inside Diameter, in (mm) ........ 1,75 (44,45)
Thrust Washer Thickness, in (mm) ........ 0,216-0,218 (5,47-5,54)
Cylinder Block Recess Depth for Thrust Washer (Early), in (mm) ........ 0,152-0,154 (3,86-3,91)
Cylinder Block Recess Depth for Thrust Washer (Later), in (mm) ........ 0,187-0,190 (4,75-4,83)
Cylinder Block Recess Depth for Thrust Washer (Current), in (mm) ........ 0,215-0,218 (5,46-5,53)
Thrust Washer Protrusion beyond Cylinder Block Front Face (Early), in (mm) ........ 0,062-0,066 (1,53-1,68)
Thrust Washer Protrusion beyond Cylinder Block Front Face (Later), in (mm) ........ 0,026-0,031 (0,66-0,79)
Thrust Washer Relationship to Cylinder Block Front Face (Current), in (mm) ........ -0,002-+0,003 (-0,05-+0,07)
Camshaft End Float, in (mm) ........ 0,004-0,016 (0,10-0,41)
Lubricating System
Relief Valve Length of Plunger Outside Diameter of Plunger, in (mm) ........ 0,826 (20,98)
Relief Valve Inside Diameter of Valve Housing Bore, in (mm) ........ 0,5585-0,5595 (14,186-14,211)
Relief Valve Clearance of Plunger in Bore Outside Diameter of Spring, in (mm) ........ 0,570 (14,5)
Oil Capacity (Standard) ........ 8.4 qts (8 litres)
Cooling System
Engine Water Capacity (Less Radiator) ........ 9.7 qts (9.36 litres)
Thermostat Type ........ Bellows or Wax
Opening Temperature Fully ........ 170-180 F (77-83C)
Water Pump Type ........ Centrifugal
Water Pump Outside Diameter of Shaft for Pulley, in (mm) ........ 0,7492-0,7497 (19,03-19,04)
Water Pump Inside Diameter of Pulley Bore, in (mm) ........ 0,7508-0,7516 (19,07-19,0)
Water Pump Clearance Fit of Pulley on Shaft, in (mm) ........ 0,0011-0,0024 (0,03-0,06)
Water Pump Outside Diameter of Shaft for Impeller, in (mm) ........ 0,6262-0,6267 (15,90-15,92)
Water Pump Inside Diameter of Impeller Bore, in (mm) ........ 0,6249-0,6257 (15,87-15,89)
Perkins 4.248 Tightening Torque Specs
Cylinder Head Nuts/Setscrews (1/2 in), Nm (Ibf-ft) ........ 136 (100)
Cylinder Head Setscrews with Integral Head, Nm (Ibf-ft) ........ 120 (88)
Connecting Rod Nuts, Nm (Ibf-ft) ........ 122 (90)
Main Bearing Setscrews, Nm (Ibf-ft) ........ 244 (180)
Idler Gear Hub Setscrews, Nm (Ibf-ft) ........ 41 (30)
Fuel Injection Pump Gear Retaining Setscrews, Nm (Ibf-ft) ........ 27 (20)
D.P.S. Fuel Injection Pump Gear Retaining Nut, Nm (Ibf-ft) ........ 81 (60)
Flywheel Setscrews, Nm (Ibf-ft) ........ 108 (80)
Flywheel Place Bolts, Nm (Ibf-ft) ........ 122 (90)
Flywheel Housing Setscrews (Standard), Nm (Ibf-ft) ........ 49 (36)
Camshaft Gear Retaining Setscrews, Nm (Ibf-ft) ........ 68 (50)
Crankshaft Pulley Retaining Setscrew, Nm (Ibf-ft) ........ 406 (300)
Oil Filter Setscrews/Nuts, Nm (Ibf-ft) ........ 41 (30)
Atomiser Securing Nuts, Nm (Ibf-ft) ........ 18 (14)
Atomiser Clamp Nuts, Nm (Ibf-ft) ........ 12 (9)
Rockershaft Support Brackets (Cast Iron), Nm (Ibf-ft) ........ 74 (54)
High Pressure Fuel Pipe Nuts, Nm (Ibf-ft) ........ 20 (15)
Dynamo Pulley Retaining Nut, Nm (Ibf-ft) ........ 27 (20)
Alternator Pulley Retaining Nut, Nm (Ibf-ft) ........ 41 (30)
Balancer Retaining Setscrews, Nm (Ibf-ft) ........ 50 (40)
________________________________________________________________________________________
Perkins A4.212
Perkins AD3.152
Perkins 4.236
Perkins F3.144
Perkins 4.154
________________________________________________________________________________
________________________________________________________________________________________
DIESEL ENGINES SPECS AND SERVICE DATA |
Perkins 4.248
Perkins A4.212
Perkins AD3.152
Perkins 4.236
Perkins F3.144
________________________________________________________________________________________
Perkins 4.108
Perkins 4.154
Perkins 1004.42
Perkins 1004.4T
Perkins 1004.40T
________________________________________________________________________________________
Perkins 1004.4
Perkins 1004.40
Perkins 1006.6T
Perkins 1006.60T
Perkins 1006.6
________________________________________________________________________________________
Yanmar 3TNA72
Yanmar 3TNE68
Yanmar 3TNE74
Yanmar 3TNV70
Yanmar 3TNV76
________________________________________________________________________________________
________________________________________________________________________________________
Yanmar 3TNV82A
Yanmar 3TNV88
Yanmar 4TNE84
Mitsubishi_K3E
Mitsubishi_S3L
________________________________________________________________________________________
Kubota D902
Kubota D905
Kubota D950
Kubota D1005
Kubota D1100
________________________________________________________________________________________
Kubota D1105
Kubota D1503
Kubota D1703
Kubota D1803
Kubota V1200
________________________________________________________________________________________
Kubota V1205
Kubota V1305
Kubota V1505
Kubota V2203
Kubota V2403
________________________________________________________________________________________
GASOLINE ENGINES SPECS AND SERVICE DATA |
CH12.5
CH14S
CH15S
CH16
CH18S
________________________________________________________________________________________
CH23S
CH25S
CH640S
CH730S
CH750S
________________________________________________________________________________________
CV740S
K161
K181
K241
K301
________________________________________________________________________________________
K321
K341
K361
M18
M20
________________________________________________________________________________________
SV470S
SV530S
SV540S
SV590S
SV600S
________________________________________________________________________________________
FA210
FA210D
FB460V
FC150V
FC290V
________________________________________________________________________________________
FC420V
FC540V
FD501V
FD590V
FD620D
________________________________________________________________________________________
FD731V
FD750D
FH430V
FH500V
FH531V
________________________________________________________________________________________
FH580V
FH601V
FH680V
FS541V
FS600V
________________________________________________________________________________________
FS651V
FX651V
FX691V
FX730V
FS541V
________________________________________________________________________________________
Kubota D902 Fuel System
Kubota B1550, B6100, B6200 Engine Service
Kubota B5200, B7100, B7100HST Engine Service
Kubota B1700, BX2200, B8200 Engine Check and Maintenance
Kubota L245DT, L2350, L2550 Engine Service and Maintenance
Kubota L2800, L3010, L3130 Engine Checking and Service
Kubota L2501, L3200, L3400, L3800 Engine Service and Maintenance
Kubota L5040, L5740, MX5100, L4200 Engine Service
JD 3120, 3320, 3520, 3720 Engine
JD 3032E, 3038E Service Engine
JD 5620, 5720 Engine
JD 5225, 5325, 5525 Engine
JD 4044R, 4052R Service Engine